Tuesday, July 18, 2017

64 Channels Digital Video Optical Transceiver

www.mootek.in              16 Channels Digital Video Optical Transceiver


Model : SWV66400

3onedata digital video optical transceivers SWV66400 series can simultaneously transmit 64 channels of 8-bit digitally encoded broadcast quality video/return or bidirectional data/unidirectional or bidirectional audio/Ethernet/Telephone/Dry contact over one multimode or single-mode optical fiber. These multiplexers are typically used in applications where the cameras have P/T/Z capabilities. Plug and Play design ensures the ease of installation and operation. Electronic and optical adjustments are never required. LED indicators are provided for instantly monitoring system status. Devices are available for either standalone or rack-mount installation, which is suitable for different working environment.


    Features
    1.8-bit digitally encoded and non-compression broadcast quality video transmission
    2.Directly compatible with NTSC, PAL, and SECAM CCTV camera systems and support RS-232, RS-422, and RS-485 data protocols
    3.Support any high-resolution video signal
    4.Automatic compatible PAL, NTSC and SECAM video system
    5.Power supply and other parameter state indication, which can monitor the operation condition of system
    6.Support no-damage regenerative trunk of video
    7.Constant input optical power, and large dynamic range ,no Electrical or Optical Adjustments Required
    8.Special ASIC design
    9.Industry-grade of operating temperature from -10°C to 65°C , which is applied to the different working environment
    10.Hot-swap function
    11.Stand-alone type or card-type installed in 19"4U rack-mount chassis

    Specification
    Technical Specification
    Video channels:64 channels
    Video bandwidth:8 MHz
    Automatic compatible video system:PAL, NTSC, SECAM
    Video input/output impedance:75 Ω(unbalance)
    Video signal-to-noise ratio:≥67dB
    Differential gain:(10%-90%APL) DG <1% ( typical value)
    Differential phase:(10%-90%APL) DP <0.7° ( typical value)
    Video connector:BNC
    Fiber-optic Specification
    F/O connector: FC/ST/SC
    TX :Power:-15 ~ -8dBm   Sensitivity :≤-35dBm
    RX:Power:-15 ~ -8dBm   Sensitivity :≤-35dBm
    Transmission Distance :20KM (single mode)
    Operating Wavelength: TX1310/RX1550nm (Transmitter); TX1550/RX1310nm (Receiver)
    Specification of custom-made options
    1. Data
    Connector: Terminal Blocks
    Encoded type : RS485 / RS422 / RS232 / Manchester
    Data rate : 0 - 400Kbps
    BER:  ≤10-9
    2. Audio
    Connector: Terminal Blocks
    Audio input / output impedance :600Ω(Balance/ unbalance)
    Audio input / output voltage :2Vp-p ( typical value)
    Audio input / output level :0dBm ( typical value)
    Video bandwidth:10HZ~12KHZ
    Audio digital encoded bandwidth :24bit
    Audio signal-to-noise ratio: S/N≥95dB  (weighted)
    3. Telephone
    Connector: RJ11
    Bandwidth :8KHZ
    Features:Support call-showing function ;support H-F
    Operating mode : Point to point hotline mode / FXS-FXO
    4. Ethernet
    Connector: RJ45
    Support mode : Half duplex or Full duplex
    Standards:IEEE802.3
    Data rate : 10M / 100Mbps
    Bandwidth: 25M
    Characteristic
    Dimensions: 48.3(L)×22(W)×4.4(H) cm(19”4U)
    Operating Voltage: AC96-240V
    Operating Temperature: -10°C to +65°C
    Storing Temperature: -45°C to +85°C
    Humidity: 0 to 95% non-condensing
    MTBF: ≥10 hours

FOR ANY ENQUIRY 9941522520

1 comment:

  1. ESIMs are currently used by a few select carriers and devices, but their use is expected to become more widespread in the near future. One advantage of eSIMs over physical SIM cards is that they are much easier to switch between different carriers. For example, if you have an eSIM-enabled device, you can simply go into your settings and change your carrier without having to obtain a new SIM card. International Data eSIM card

    ReplyDelete