2 Channels Digital Video Optical Transceiver

              2 Channels Digital Video Optical Transceiver

Model : SWV60200

3onedata digital video optical transceivers SWV60200 series can simultaneously transmit 2 channels of 8-bit digitally encoded broadcast quality video/return or bidirectional data/unidirectional or bidirectional audio/Ethernet/Telephone/Dry contact over one multimode or single-mode optical fiber. These multiplexers are typically used in applications where the cameras have P/T/Z capabilities. Plug and Play design ensures the ease of installation and operation. Electronic and optical adjustments are never required. LED indicators are provided for instantly monitoring system status. Devices are available for either standalone or rack-mount installation, which is suitable for different working environment.

Features
1.8-bit digitally encoded and non-compression broadcast quality video transmission 
2.Directly compatible with NTSC, PAL, and SECAM CCTV camera systems and support RS-232, RS-422, and RS-485 data protocols
3.Support any high-resolution video signal  
4.Automatic compatible PAL, NTSC and SECAM video system 
5.Power supply and other parameter state indication, which can monitor the operation condition of system 
6.Support no-damage regenerative trunk of video 
7.Constant input optical power, and large dynamic range ,no Electrical or Optical Adjustments Required 
8.Special ASIC design
9.Industry-grade of operating temperature from -10°C to 65°C , which is applied to the different working environment
10.Hot-swap function 
11.Stand-alone type or card-type installed in 19"4U rack-mount chassis
 
Specification
Technical Specification
Video channels：2 channels
Video bandwidth：8 MHz
Automatic compatible video system：PAL, NTSC, SECAM
Video input/output impedance：75 Ω(unbalance)
Video signal-to-noise ratio：≥67dB
Differential gain：(10%-90%APL) DG <1% ( typical value)
Differential phase：(10%-90%APL) DP <0.7° ( typical value)
Video connector：BNC
Fiber-optic SpecificationF/O connector: FC/ST/SC
TX ：Power:-15 ~ -8dBm   Sensitivity :≤-35dBm 
RX：Power:-15 ~ -8dBm   Sensitivity :≤-35dBm
Transmission Distance :20KM (single mode)
Operating Wavelength: TX1310/RX1550nm (Transmitter); TX1550/RX1310nm (Receiver)
Specification of custom-made options
1. Data
Connector: Terminal Blocks
Encoded type : RS485 / RS422 / RS232 / Manchester
Data rate : 0 - 400Kbps
BER:  ≤10-9
2. Audio
Connector: Terminal Blocks
Audio input / output impedance :600Ω(Balance/ unbalance)
Audio input / output voltage :2Vp-p ( typical value)
Audio input / output level :0dBm ( typical value)
Video bandwidth:10HZ~12KHZ
Audio digital encoded bandwidth :24bit
Audio signal-to-noise ratio: S/N≥95dB  (weighted)
3. Telephone
Connector: RJ11
Bandwidth :8KHZ
Features：Support call-showing function ;support H-F
Operating mode : Point to point hotline mode / FXS-FXO
4. Ethernet
Connector: RJ45
Support mode : Half duplex or Full duplex
Standards：IEEE802.3 
Data rate : 10M / 100Mbps 
Bandwidth: 25M
Characteristic
Dimensions: 19.2(L)×17.3(W)×2.8(H) cm
Operating Voltage: DC5V (we will offer external power supply from AC96-240V to DC5V for each unit )
Operating Temperature: -10°C to +65°C
Storing Temperature: -45°C to +85°C
Humidity: 0 to 95% non-condensing
MTBF: ≥10 5 hours

Video Optical Transceiver

                            Video Optical Transceiver

3onedata digital video optical transceivers SWV60100 series can simultaneously transmit 1 channel of 8-bit digitally encoded broadcast quality video/return or bidirectional data/unidirectional or bidirectional audio/Ethernet/Telephone/Dry contact over one multimode or single-mode optical fiber. These multiplexers are typically used in applications where the cameras have P/T/Z capabilities. Plug and Play design ensures the ease of installation and operation. Electronic and optical adjustments are never required. LED indicators are provided for instantly monitoring system status. Devices are available for either standalone or rack-mount installation, which is suitable for different working environment.

Features
1.8-bit digitally encoded and non-compression broadcast quality video transmission 
2.Directly compatible with NTSC, PAL, and SECAM CCTV camera systems and support RS-232, RS-422, and RS-485 data protocols
3.Support any high-resolution video signal  
4.Automatic compatible PAL, NTSC and SECAM video system 
5.Power supply and other parameter state indication, which can monitor the operation condition of system 
6.Support no-damage regenerative trunk of video 
7.Constant input optical power, and large dynamic range ,no Electrical or Optical Adjustments Required .
8.Special ASIC design .
9.Industry-grade of operating temperature from -10°C to 65°C , which is 
10.applied to the different working environment
11.Hot-swap function 
 
Specification
Technical Specification
Video channels：1 channel
Video bandwidth：8 MHz
Automatic compatible video system：PAL, NTSC, SECAM
Video input/output impedance：75 Ω(unbalance)
Video signal-to-noise ratio：≥67dB
Differential gain：(10%-90%APL) DG <1% ( typical value)
Differential phase：(10%-90%APL) DP <0.7° ( typical value)
Video connector：BNC
Fiber-optic Specification
F/O connector: FC/ST/SC
TX ：Power:-15 ~ -8dBm   Sensitivity :≤-35dBm 
RX：Power:-15 ~ -8dBm   Sensitivity :≤-35dBm
Transmission Distance :20KM (single mode)
Operating Wavelength: TX1310/RX1550nm (Transmitter); TX1550/RX1310nm (Receiver)
Specification of custom-made options
1. Data
Connector: Terminal Blocks
Encoded type : RS485 / RS422 / RS232 / Manchester
Data rate : 0 - 400Kbps
BER:  ≤10-9
2. Audio
Connector: Terminal Blocks
Audio input / output impedance :600Ω(Balance/ unbalance)
Audio input / output voltage :2Vp-p ( typical value)
Audio input / output level :0dBm ( typical value)
Video bandwidth:10HZ~12KHZ
Audio digital encoded bandwidth :24bit
Audio signal-to-noise ratio: S/N≥95dB  (weighted)
3. Telephone
Connector: RJ11
Bandwidth :8KHZ
Features：Support call-showing function ;support H-F
Operating mode : Point to point hotline mode / FXS-FXO
4. Ethernet
Connector: RJ45
Support mode : Half duplex or Full duplex
Standards：IEEE802.3 
Data rate : 10M / 100Mbps 
Bandwidth: 25M
Characteristic
Dimensions: 11.1(L)×10.7(W)×2.8(H) cm
 Operating Voltage: DC5V (we will offer external power supply from AC96-240V to DC5V for each unit )
Operating Temperature: -10°C to +65°C
Storing Temperature: -45°C to +85°C
Humidity: 0 to 95% non-condensing

1 Channel Mini Digital Video Optical Transceiver

                    Digital Video Optical Transceiver

Model : SWV60100

3onedata digital video optical transceivers SWV60100 series can simultaneously transmit 1 channel of 8-bit digitally encoded broadcast quality video/return or bidirectional data/unidirectional or bidirectional audio/Ethernet/Telephone/Dry contact over one multimode or single-mode optical fiber. These multiplexers are typically used in applications where the cameras have P/T/Z capabilities. Plug and Play design ensures the ease of installation and operation. Electronic and optical adjustments are never required. LED indicators are provided for instantly monitoring system status. Devices are available for either standalone or rack-mount installation, which is suitable for different working environment.

Digital Video Optical Transceiver

                       Digital Video Optical Transceiver

SWV60100

3onedata digital video optical transceivers SWV60100 series can simultaneously transmit 1 channel of 8-bit digitally encoded broadcast quality video/return or bidirectional data/unidirectional or bidirectional audio/Ethernet/Telephone/Dry contact over one multimode or single-mode optical fiber. These multiplexers are typically used in applications where the cameras have P/T/Z capabilities. Plug and Play design ensures the ease of installation and operation. Electronic and optical adjustments are never required. LED indicators are provided for instantly monitoring system status. Devices are available for either standalone or rack-mount installation, which is suitable for different working environment.

Features
1.8-bit digitally encoded and non-compression broadcast quality video transmission 
2.Directly compatible with NTSC, PAL, and SECAM CCTV camera systems and support RS-232, RS-422, and RS-485 data protocols
3.Support any high-resolution video signal  
4.Automatic compatible PAL, NTSC and SECAM video system 
5.Power supply and other parameter state indication, which can monitor the operation condition of system 
6.Support no-damage regenerative trunk of video 
7.Constant input optical power, and large dynamic range ,no Electrical or Optical Adjustments Required .
8.Special ASIC design .
9.Industry-grade of operating temperature from -10°C to 65°C , which is 
10.applied to the different working environment
11.Hot-swap function 
 
Specification
Technical Specification
Video channels：1 channel
Video bandwidth：8 MHz
Automatic compatible video system：PAL, NTSC, SECAM
Video input/output impedance：75 Ω(unbalance)
Video signal-to-noise ratio：≥67dB
Differential gain：(10%-90%APL) DG <1% ( typical value)
Differential phase：(10%-90%APL) DP <0.7° ( typical value)
Video connector：BNC
Fiber-optic Specification
F/O connector: FC/ST/SC
TX ：Power:-15 ~ -8dBm   Sensitivity :≤-35dBm 
RX：Power:-15 ~ -8dBm   Sensitivity :≤-35dBm
Transmission Distance :20KM (single mode)
Operating Wavelength: TX1310/RX1550nm (Transmitter); TX1550/RX1310nm (Receiver)
Specification of custom-made options
1. Data
Connector: Terminal Blocks
Encoded type : RS485 / RS422 / RS232 / Manchester
Data rate : 0 - 400Kbps
BER:  ≤10-9
2. Audio
Connector: Terminal Blocks
Audio input / output impedance :600Ω(Balance/ unbalance)
Audio input / output voltage :2Vp-p ( typical value)
Audio input / output level :0dBm ( typical value)
Video bandwidth:10HZ~12KHZ
Audio digital encoded bandwidth :24bit
Audio signal-to-noise ratio: S/N≥95dB  (weighted)
3. Telephone
Connector: RJ11
Bandwidth :8KHZ
Features：Support call-showing function ;support H-F
Operating mode : Point to point hotline mode / FXS-FXO
4. Ethernet
Connector: RJ45
Support mode : Half duplex or Full duplex
Standards：IEEE802.3 
Data rate : 10M / 100Mbps 
Bandwidth: 25M
Characteristic
Dimensions: 11.1(L)×10.7(W)×2.8(H) cm
 Operating Voltage: DC5V (we will offer external power supply from AC96-240V to DC5V for each unit )
Operating Temperature: -10°C to +65°C
Storing Temperature: -45°C to +85°C
Humidity: 0 to 95% non-condensing
MTBF: ≥10 5 hours

1 Channel Mini Digital Video Optical Transceiver

           1 Channel Mini Digital Video Optical Transceiver

Model : SWV60100

3onedata digital video optical transceivers SWV60100 series can simultaneously transmit 1 channel of 8-bit digitally encoded broadcast quality video/return or bidirectional data/unidirectional or bidirectional audio/Ethernet/Telephone/Dry contact over one multimode or single-mode optical fiber. These multiplexers are typically used in applications where the cameras have P/T/Z capabilities. Plug and Play design ensures the ease of installation and operation. Electronic and optical adjustments are never required. LED indicators are provided for instantly monitoring system status. Devices are available for either standalone or rack-mount installation, which is suitable for different working environment.

Features

1.8-bit digitally encoded and non-compression broadcast quality video transmission 
2.Directly compatible with NTSC, PAL, and SECAM CCTV camera systems and support RS-232, RS-422, and RS-485 data protocols
3.Support any high-resolution video signal  
4.Automatic compatible PAL, NTSC and SECAM video system 
5.Power supply and other parameter state indication, which can monitor the operation condition of system 
6.Support no-damage regenerative trunk of video 
7.Constant input optical power, and large dynamic range ,no Electrical or Optical Adjustments Required .
8.Special ASIC design .
9.Industry-grade of operating temperature from -10°C to 65°C , which is 
10.applied to the different working environment
11.Hot-swap function

Specification

Technical Specification
Video channels：1 channel
Video bandwidth：8 MHz
Automatic compatible video system：PAL, NTSC, SECAM
Video input/output impedance：75 Ω(unbalance)
Video signal-to-noise ratio：≥67dB
Differential gain：(10%-90%APL) DG <1% ( typical value)
Differential phase：(10%-90%APL) DP <0.7° ( typical value)
Video connector：BNC
Fiber-optic Specification
F/O connector: FC/ST/SC
TX ：Power:-15 ~ -8dBm   Sensitivity :≤-35dBm 
RX：Power:-15 ~ -8dBm   Sensitivity :≤-35dBm
Transmission Distance :20KM (single mode)
Operating Wavelength: TX1310/RX1550nm (Transmitter); TX1550/RX1310nm (Receiver)
Specification of custom-made options
1. Data
Connector: Terminal Blocks
Encoded type : RS485 / RS422 / RS232 / Manchester
Data rate : 0 - 400Kbps
BER:  ≤10-9
2. Audio
Connector: Terminal Blocks
Audio input / output impedance :600Ω(Balance/ unbalance)
Audio input / output voltage :2Vp-p ( typical value)
Audio input / output level :0dBm ( typical value)
Video bandwidth:10HZ~12KHZ
Audio digital encoded bandwidth :24bit
Audio signal-to-noise ratio: S/N≥95dB  (weighted)
3. Telephone
Connector: RJ11
Bandwidth :8KHZ
Features：Support call-showing function ;support H-F
Operating mode : Point to point hotline mode / FXS-FXO
4. Ethernet
Connector: RJ45
Support mode : Half duplex or Full duplex
Standards：IEEE802.3 
Data rate : 10M / 100Mbps 
Bandwidth: 25M
Characteristic
Dimensions: 11.1(L)×10.7(W)×2.8(H) cm
 Operating Voltage: DC5V (we will offer external power supply from AC96-240V to DC5V for each unit )
Operating Temperature: -10°C to +65°C
Storing Temperature: -45°C to +85°C
Humidity: 0 to 95% non-condensing

18 ports 10/100/1000M PoE Switch

18 ports 10/100/1000M PoE Switch

Product Description

 ES5018G-2GS-16POE-300W is Full gigabit , managed, 18-port Gigabit high power (IEEE 802.3at) PoE Switche,utilizing a compact factor which can be mounted in a 19-inch rack with rack-mounting kits or placed on desktop. 
With data and power supported by one unit, the ES5018G-2GS-16POE-300W-P(220VAC) shall reduce cables and eliminate the need for dedicated electrical outlets on the wall,ceiling or any unreachable place. Auto PoE detection and Plug and play installation makes ES5018G-2GS-16POE-300W-P(220VAC) Gigabit PoE Switch easy to use and with clear LED indicators to tell the working condition.

Features
1. Compatible with both IEEE802.3at(30W) and IEEE802.3af(15.4W)
2. Automatically detect and supply power to IEEE802.3at and IEEE 802.3af compliant powered devices(PDs)
3. Advanced SAFC function, only supply power to IEEE 802.3af/at compliant PDs, no worry about damaging 
other private standard POE devices or devices without POE function
4. Support port power supply prioritization, guarantee the continuous power supply of key nodes
5.Up to 100m network cable transmitting distance
6.Built-in PSE power supply module, plug-and play design, easy to install
7. High security performance defending against power surge
8.Support short-circuit protection function
9.Energy-saving green design, support auto-switch to standby mode and auto-detect cable length.
10.Support simple WEB management, easy to configure the functions of switches
 
Specification
Technology:
Standard and Protocols: IEEE 802.3af, Power Over Ethernet, IEEE 802.3at, Power Over Ethernet Plus
IEEE 802.3u, 100BASE-TX, IEEE 802.3ab, 1000 BASE-T, IEEE 802.3z, 1000 BASE-X, IEEE 802.3ad, Static or Dynamic Link Aggregation, IEEE 802.3x, Full-Duplex Flow Control, IEEE 802.3az, EEE(Energy Efficient Ethernet), IEEE 802.1q ,VLAN
IEEE 802.1p, QoS/CoS, IEEE 802.1d, STP(Spanning Tree Protocol), IEEE 802.1w, Rapid Spanning Tree Protocol
POE Standard: IEEE802.3af/at 
Flow control: Back-pressure traffic control under Half-Duplex mode, IEEE 802.3x traffic control under Full-Duplex mode
Ports:
Fixed ports: 16*10/100/1000M PoE ports+2* Gigabit SFP ports
PoE Pin-out: 1/2(+), 3/6(-); Customized 4/5(+),7/8(-)
Exchange Properties:
100M forwarding rate: 1488095pps
100M forwarding rate: 148809pps
10M forwarding rate: 14880pps
Transmit type: Full wire-speed storage and forwarding
MAC address: 16K, Support auto-update, two-way learning
VLAN: Support up to 4096 VLANs,Port-based VLANs,VLANs based on IEEE 802.1q
Switching Capacity: ≥36Gbps
Spanning Tree: Spanning Tree Protocol, Rapid Spanning Tree Protocol(RSTP),          
Link Aggregation:Support 8 aggregation groups, and a maximum of 4 ports in each aggregation group
Ring Protection:Support Ring Protection, provide real-time detecting, quick alarm, precise localization, smart blocking and auto-recovery
Port Isolation: Isolation between downlink ports without influence the communication between downlink and uplink ports
Port Flow Control: Back-pressure traffic control under Half-Duplex mode, IEEE 802.3x traffic control under Full-Duplex mode
Port Rate Restriction: Port-based ingress or egress rate limiting
Jumbo Frame: Maximum supports 9216 Byte
Storm Suppression: Support the suppression of broadcast storm based on forwarding rate
Multicast Control: Support IGMPv1/2/3 and MLDv1/2 Snooping;
Security:Port-base MAC address binding,Security restriction on port-based MAC address quantity
QOS: SP(Strict Priority), WFQ (Weighted Fair Queuing), WRR (Weighted Round Robin), 802.1p(Port Queuing Priority), Differentiated Service Code Point(DSCP Priority)
IPv6:IPv6 Parsing
PoE ouput priority Management: Supported
Physic Medium: 
10/100Base-TX: UTP category 3/4/5 cables( Maximum 100m)
1000Base-T: UTP Category 5 cable( Maximum 100m)
1000Base-SX: fiber with 850nm wavelength, supports a max transmission distance of 550m
1000Base-LX: fiber with 1310nm / 1550nm wavelength, supports a max transmission distance of 80km
Network Cable Deployment:Support Auto-MDIX function, automatically identify straight forward cable and cross-over cable 
Negotiation Pattern: Support port auto-negotiation function ( automatically negotiate transmission rate and Duplex modes)
Maintenance: Detect the connectivity of network cables,Uploading or downloading of the configuration data,Uploading of upgrade patch, WEB-based reset to factory defaults, Support port short-circuit reset to factory defaults
Management: Support WEB-based management
Indicator light:
Interface light: Link/Act, POE Status
Power light: PWR
Power:
Input Power Supply: 90～264VAC/50～60Hz/300W
Energy Saving:Comply with “EEE” Energy Efficient Ethernet 
Working Environment:
Working Temperature: -20~50°C
Storage Temperature: -40~70°C
Operation Humidity:10%～90%(non-condensing)
Storage Humidity:5%～95%(non-condensing)
Mechanical Properties:
Weight: <8Kg
Dimensions(L×W×H):440×285×44.5mm

14 Ports 10/100/1000M Managed Industrial POE Switch

14 Ports 10/100/1000M Managed Industrial POE Switch

Product Description

 The Managed Industrial Fiber POE Switch LIMPOX14-4SFP features total 10x RJ45port (10/100/1000M) with 4x SFP ports (1000M). It supports wide operating temperature (-40 to +75degreeC). Its casing is IP40 rated and meet EMC industrial level 4 requirements. These switches are specially designed for harsh industrial environments certified by UL508 and UL Class 1 Div 2 requirements. It is suitable for wind power, subway PIS, power SCADA, sewage treatment, intelligent transportation systems applications.

• Managed Switch with 10x 10/100/1000Base-T ports, 4x Gigabit SFP slots, and 1 console port
• L2+ features provide better manageability, security, QoS, and performance.
• Support L2+ Switching features including 802.1Q VLAN, Mirroring, Port isolation, IGMP Snooping, DHCP Snooping, LLDP, IP Source Guard, ARP inspection, ACLs etc.
• Support spanning tree STP(802.1D) and RSTP(802.1W).
• Jumbo frames support up to 9.6K kilobytes.
• Support enhanced management through WEB, CLI, TELNET, SSH, SNMP.
• Support cable diagnosis
• Supports both IEEE 802.3af and 802.3at (4ports), and every port PoE
  configuration function
• G.8032, support <50ms industrial quick ring protection

Specification:

14Ports 10/100/1000M Managed Industrial POE Switch with 4Ports SFP 1000MNumber of RJ45 ports (10/100/1000BaseT)10 (Ethernet port, POE supported)Number of SFP ports (1000M)4Optical portsSFPLayer2 switchingSpanning Tree Protocol (STP)Standard Spanning Tree 802.1d Rapid Spanning Tree (RSTP) 802.1wG.8032 ERPS<50ms ring protection for industrial ring applicationAggregationLink Aggregation Control Protocol (LACP) IEEE802.3ad; up to 7 groups &
14ports per groupVLANSupport up to 4k VLANs simultaneously (out of 40906 VLAN IDs); Port based
VLAN; 802.1Q tag based VLANIGMP v1/v2 snoopingIGM limits bandwidth intensive multicast traffic to only the requesters.
Support 1024 multicast groups (source-specific multicasting is not supported)POE standard /typeIEEE802.3af/at, END SPANMax POE Power per port15.4W per port (IEEE802.3af) & 30W per port (IEEE802.3at), total 4portsSecurity Secure Shell (SSH) ProtocolSSH secures Telnet traffic in or out the switch, SSH v1 and v2 are supportedSecure Sockets Layer (SSL), HTTPSSSL encrypts the http traffic, allowing advance secure access to the browser-based
management GUI in the switchPort SecurityLocks MAC Addresses to ports, and limits the number of learned MAC addressesDHCP Snoopingprevent unauthorized configuration and use of IP addresses, while providing
support for IP Source Guard and ARP detectionIP Source GuardPrevents datagram with spoofed addresses from being in the networkARP InspectionPrevent ARP spoofing attacks and ARPStorm ControlPrevents traffic on a LAN from being disrupted by a broadcast, multicast,
or unicast storm on a portACLsSupport for up to 256 entries; Drop or rate limitation based on source
and destination MAC, VLAN ID or IP address, protocol, port, differentiated
services code point (DSCP) / IP precedence, TCP/ UDP source and destination
ports, 802.1p priority, Ethernet type, Internet Control Message Protocol
(ICMP) packets, IGMP packets, TCP flagQualtiy of Service HardwareSupport 8 hardware queuesScheduling8 COS queues per port support strict priority and weighted round-robin
(WRR)ClassificationsPort based; 802.1p(PCP) VLAN priority based;Rate LimitingIngress policer;egress shaping and rate control;per VLAN,per port and
flow basedManagement (Web/ SSL, Telnet/ SSH, ping,
Trivial File Transfer Protocol (TFTP), SNMP, Syslog)Web GUIBuilt-in switch configuration utility for browser-based device configuration
(HTTP/ HTTPs). Supports configuration, system dashboard, maintenance, and
monitoringDual ImageDual image provides independent primary and secondary OS files for backup
while upgradingFirmware upgradeWeb browser upgrade (HTTP/ HTTPs) and TFTP;??Upgrade through console port
as wellPort mirroringTraffic on a port can be mirrored to another port for analysis with a
network analyzer or RMON probe. Up to N-1 (N is Switch’s Ports) ports can
be mirrored to single destination port. A single session is supported.OthersSingle IP management; HTTP/HTTPs; SSH; RADIUS; DHCP Client; SNTP; cable
diagnostics; ping; syslog; Telnet client (SSH secure support)Green Ethernet Green and Energy saving Ethernet (EEE)Compliant IEEE802.3az Energy Efficient Ethernet Task Force. Automatically
turns off power on Gigabit Ethernet RJ-45 port when detecting link down
or Idle of client. Active mode is resumed without loss of any packets when
the switch detects the link upCable length detectionAdjusts the signal strength based on the cable length. Reduces the power
consumption for cables shorter.General Jumbo framesFrame sizes up to 9KB supported on Gigabit interfacesMac tableUp to 8k Mac addressDiscovery Link Layer Discovery Protocol (LLDP)Used by network devices for advertising their identities, capabilities,
and neighbors on a IEEE 802 local area network, principally wired Ethernet.Min Requirements  Web browser: Mozilla Firefox version 2.5 or later, Microsoft Internet
Explorer version 6 or later; Category 5 Ethernet network cable; TCP/IP,
network adapter, and network operating system (such as Microsoft Windows,
Linux, or Mac OS X) installed on each computer in networkDimensions165x145x45mmWorking EnvironmentOperating temperature: -40 to 75 ℃; Storage temperature: -40℃ to 75 ℃;
Operating humidity: 10% to 90% , relative, non-condensing

ES1009D-8POE-150W(8 ports 10/100M PoE Switch)(stop production)

ES1009D-8POE-150W(8 ports 10/100M PoE Switch)(stop production)

Model : ES1009D-8POE-150W

ES1009D-8POE-150W are 10/100M unmanaged PoE Switches. The PoE switches are specifically designed to meet IEEE 802.3af standards for powering network devices, supports 8 POE port and 1 uplink port. Uplink ports can be connected other specifications switches, routers, ordinary PC and terminal can also be connected with the NVR security equipment, this design with the characteristics of security industry network construction, port utilization rate is extremely high. This product supports the 802.3af/at IEEE Ethernet power supply standard, provide the 48V national standard power supply, remote power feeding up to 100m, only for the 802.3af/at standard terminal equipment power supply. It can seamlessly connect IP network monitoring camera, network HD camera security monitoring equipment, etc. Compared with ordinary PoE products, ES1009D-8POE-150W products with high power, PoE power supply and lightning protection, it is an ideal choice for the security of network equipment.

Features
1.Separate uplink ports designed to meet the security industry networking features.
2.Supports IEEE802.3af standard, full-port full 15.4W power supply;
3.Supports IEEE802.3at standard, single-port maximum 30W power supply;
4.Metal shell, no fan, both sides of the cabinet have thermal design;
5.Supports port auto-flip (Auto MDI / MDIX), network transport 100 meters without interruption;
6.Only IEEE 802.3af / at-compliant end device powered private standard PoE or PoE device access is not recognized, it will not be damaged;
7.High-quality components, high specification resistance design, equipment grounding screw,reducing the risk of lightning strikes.
8.External power supply, the total power 96W;
9.Per-port power LED indicator design, visual observation whether the access terminal, power supply is normal;
10.All port 10 / 100M adaptive, wire-speed store and forward;
 
Specification
Technology
Protocols Standards :
IEEE 802.3,10BASE-T      
IEEE 802.3u,100 BASE-TX      
IEEE 802.3af,Power Over Ethernet 
IEEE 802.3at,Power Over Ethernet Plus 
IEEE 802.3az,EEE(Energy Efficient Ethernet)
IEEE 802.3x, traffic control under Full-Duplex mode
PoE Standards:IEEE 802.3af/at
Port
Fixed port : 9*10/100 Base-T ports (8*POE)
Exchange Properties
POE Pin-out : 1/2(+),3/6(-)
Switching Capacity : ≥1.8Gbps 
Forwarding mode : Full speed storage and forwarding
Packet Forwarding Capacity : 
    10M : 14880pps/port 
   100M : 148809pps/port          
Cable line sequence :Support Auto-MDIX function, automatic identification straight-through cable and the crossover cable
Negotiation Pattern:Support port auto-negotiation function (automatically negotiate transmission rate and Duplex modes)
Power requirements
Input Power Supply : 48V/2A (96W),External DC power supply 
LED Indicator
Interface light : Link/Act,POE Status
Power light : PWR
Mechanical Properties
Weight : 0.96Kg
Dimensions(L×W×H) : 155mm*75mm*28mm
Working Environment
Working Temperature : -20~50°C
Storage Temperature : -40~70°C
Operation Humidity : 10%～95%(non-condensing)

2-port 10/100M Ethernet Media Converter - Model1200

Model1200(2-port 10/100M Ethernet Media Converter)

Model : Model1200

The Media Converter complies with IEEE802.3, IEEE802.3u, IEEE802.3x Standards. It is designed to convert data signal between 10/100 Base-TX and 100Base-FX fast Ethernet. It supports 10/100Base-TX and 100Base-FX applications. The data signal converted by such high performance media converter can be transmitted up to 120Km maximum by fiber-optical cable. The Converter is equipped one optic port and two RJ45 Jacks and one external power supply receptacle. Four LED indicators are built-in for easy diagnosing and monitoring the status of. It can be configured automatically for Full Duplex or Half Duplex operation.

Features
1. Accord to IEEE802.1 10Base-T, IEEE802.3u 100Base-TX, IEEE802.3 100Base-FX
2. MDI/MDI-X auto negotiation, 10M/100M auto negotiation
3. Supports full /half duplex, Point-to-point transparent transfer
4. Power External 5VDC input
5. Plug-and-play, easy to installation
6. Can insert to 2U 19", 14 slots Rackmount
 
Specification
Standards: comply with IEEE802.1 10Base-T, IEEE802.3u 100Base-TX, IEEE802.3 100Base-FX
RJ45 port rate: 10/100Mbps auto negotiation
Optic port rate: 100Mbps 
Working: Asynchronous, point to point
Transfer distance: RJ45port: 100m
                              Fiber optic:20,40,60,80,100,120km(SM), 2 km(MM) optional
RJ45 port cable: UTP 5E 
Fiber connector: SC, ST, FC optional
Fiber optic cables: Single Mode:8.3/125,8.7/125,9/125 or 10/125 um
                                  Muti-Mode:50/125,62.5/125 um
Wavelength:850nm,1310nm,1550nm
Power
Power supply: External 5VDC input
Consumption: 4W
Environment
Operating temp:-10°C to 60°C
Storage temperature: -20 to 70°C
Operating humidity: 5% to 95%(no condensation)
Appearance
Dimensions: 94.0×71.0×26.0mm(external power supply)   
Shell: Iron 
Color: White